Fundamental Plumbing Tips for Installing a Bathtub
Fundamental Plumbing Tips for Installing a Bathtub
Blog Article
This post following next pertaining to A Step-by-Step Guide to Installing a Bathtub is extremely enlightening. You should take a peek.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately tough task. If the old tub is easily accessible, the job can relocate easily; if you need to open up a wall to eliminate the old tub as well as position the new bath tub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also set in the brand-new one. See to it you have actually qualified on your own for the work as well as fit attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is far better to think about utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and also material list ought to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, switch on the faucets to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the restricted accessibility that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers are in location between the tap and the sink. Secure the tap in position with the supplier given backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous kind must be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Using both wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the supply of water and check all joints and brand-new pipework for leaks and also tighten them if necessary. Fill up the tub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the tub ought to wait until the bathtub has been made use of a minimum of when as this will resolve it into its final placement.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, causing the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the tub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily offered on the marketplace. It is recommended to fit the tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that piece of content was worth the trouble. Sharing is good. Helping people is fun. Many thanks for your time. Visit us again soon.
Book With Us Today! Report this page